1.)
Which routing protocol include in EGP category ?
a.)
EIGRP
b.)
IS-IS
c.)
OSPF
d.)
BGP
2.)
Which routing method break the routing loop?
a.)
Auto-summarization
b.)
Split-horizon
c.)
Dis-continue network
d.)
All of above
3.)
Which hope count number considered to be
infinite by RIP.
a.)
5
b.)
10
c.)
15
d.)
16
4.)
Which update used by EIGRP ?
a.)
Periodic update
b.)
Partial update
c.)
Trigger update
d.)
None of above
5.)
Which type of session created by BGP?
a.)
Anycast
b.)
Broadcat
c.)
Unicast
d.)
Multicast
6.)
Which multicast prefix used by IPv6?
a.)
Ff00::/2
b.)
Ff00::/8
c.)
Ff02::/2
d.)
Ff02::/8
7.)
Which of the following is helpful to allow an
IPv6 host to learn the IP address of a default gateway on its subnet?
a.)
Stateful DHCP
b.)
Stateless RS
c.)
Stateless autoconfiguration
d.)
Neighbor Discovery protocol
8.)
Which command is enable IPv6 routing packet on
router?
a.)
IPv6 route packet
b.)
IPv6 unicast packet
c.)
IPv6 unicast-routing
d.)
IPv6 unicast routing
9.)
How many hex available in IPv6 single quarter?
a.)
8
b.)
4
c.)
2
d.)
16
v10.) Which IPv6 address is reserve for site-local
address?
a.)
Ffo2::/8
b.)
2000::/3
c.)
Fec0::/10
d.)
Fe80::/10
11.) In IPv6 which prefix value is called as a site
prefix/global routing prefix?
a.)
/64
b.)
/16
c.)
/48
d.)
/32
12.) EUI stand for ________ ?
a.)
Extended user interface
b.)
Extended unique interface
c.)
Extended user indentify
d.)
None of above
13.) Which multicast address use by router
solicitation in DHCPv6 process?
a.)
Ff02::2
b.)
Ff02::1
c.)
Ff02::8
d.)
Ff02::16
14.) Which multicast address used by RIPng?
a.)
Ff02::5
b.)
Ff02::1
c.)
Ff02::9
d.)
Ff02::10
15.) Dual stack approach refers to _____?
a.)
Implementing IPv4 with 2 stack
b.)
Implementing IPv6 with 2 stack
c.)
Node has both IPv4 and IPv6 support
d.)
None of above
16.) Which IPv6 address reserved for 6to4 tunneling
method?
a.)
2002::/8
b.)
2002::/32
c.)
2002::/16
d.)
2002::/48
17.) Which of the following is true when describing
an anycast address?
a.)
Packets addressed to a unicast address are
delivered to a single interface.
b.)
Packets are delivered to all interfaces
identified by the address. This is also called one-to-many address.
c.)
This address identifies multiple interface and
the anycast packet is only delivered to one address. This address can also be
called one-to-one-to-many.
d.)
These address are meant for nonrouting purpose.
18.) A router has been configured with the commands
router eigrp 9 and network
172.16.1.0 0.0.0.255. No other EIGRP related commands have been configured.
Which answer list an IP address/prefix length that would cause the router to
enable EIGRP on fastethernet 0/0?
a.)
172.16.0.1/23
b.)
172.16.1.1/26
c.)
172.16.1.1/24
d.)
172.16.0.255/23
19.) Which command is manually disable
split-horizon method in EIGRP router on serial 1/0 interface?
a.)
Interface serial 0/1
No ip split-horizon ospf 1
b.)
Interface serial 1/0
No ip split-horizon eigrp 1
c.)
Interface serial 1/0
No split-horizon eigpr 1
d.)
All of above
20.) In EIGRP metric value k4 refer to _____?
a.)
Bandwidth
b.)
Delay
c.)
Load
d.)
MTU
21.) Your company is running IGRP using an AS of
10. You want to configure EIGRP on the network but want to migrate slowly to
EIGRP and don’t want to configure redistribute. What command would allow you to
migrate over time to EIGRP without configuring restribution?
a.)
Router eigrp 11
b.)
Router eigpr 10
c.)
Router eigrp 10
d.)
Router igrp combine 10
22.) Where are EIGRP successor routes stored?
a.)
In the routing table only
b.)
In the neighbour table only
c.)
In the topology table only
d.)
In the routing and topology table
23.) Which command will display all the EIGRP
feasible successor routes known to a router?
a.)
Show ip routes *
b.)
Show ip eigrp summary
c.)
Show ip eigrp topology
d.)
Show ip eigrp adjacencies
24.) Which EIGRP information is held in RAM and
maintained through the use of Hello and update packets?
1.)
Neighbor table
2.)
STP table
3.)
Topology table
4.)
DUAL table
a.)
2 only
b.)
4 only
c.)
1 and 3
d.)
All of above
25.) If you are configure EIGRP frame relay
scenario in live field. You find out the split-horizon prevent to adjacency
from endpoint to another endpoint. Than which think you apply on it.
a.)
Point-to-point topology
b.)
Point-to-multipoint topology
c.)
Manually disable split-horizon
d.)
All of above
26.) EIGRP frame relay create network type ______ ?
a.)
Point-to-point network
b.)
NBMA network
c.)
Broadcast network
d.)
Unicast network
27.) You want to prevent any interface don’t send
own network information to another router, but it receive EIGRP adjacency,
Which think you apply on it.
a.)
MD5 authentication
b.)
EIGRP passive interface
c.)
Change hello timer
d.)
All of above
28.) Which utility use to create a link between
EIGRP routing and IP prefix-list?
a.)
Standard ACL
b.)
Extended ACL
c.)
Distribute list
d.)
Redistribute list
29.) EIGRP use AD value and algorithm ______?
a.)
DUAL and 110
b.)
DUAL and 115
c.)
DUAL and 170, 90
d.)
None of above
30.) Which type of OSPF network will elect a backup
designated router?
a.)
Non-broadcast multi-access
b.)
Point-to-point
c.)
Broadcast multipoint
d.)
None of above
31.) You get a call from a network
administrator who tells you that he
typed the following into his router:
Router(config)# router ospf 3
Router(config-router)# network 192.168.34.0
0.0.15.255 area 0
He tell you he still can’t see any routes
in the routing table. What configuration error did the administrator make?
a.)
The wildcard mask is incorrect.
b.)
The OSPF area is wrong
c.)
The ospf process ID is wrong
d.)
The network is incorrect.
32.) If routers in a single area are configured
with the same priority value, what value does a router use for the OSPF router
ID in the absence of a loopback interface?
a.)
The lowest IP address of any physical interface
b.)
The highest IP address of any physical interface
c.)
The lowest IP address of any logical interface
d.)
None of above
33.) Which command is use to view the OSPF LSA
content?
a.)
Show ip ospf neighbour
b.)
Show ip ospf traffic
c.)
Show ip ospf database
d.)
Show ip ospf account
34.) Which protocol number used by OSPF?
a.)
TCP 89
b.)
UDP 89
c.)
Transport 89
d.)
TCP and UDP 89
35.) Which one of the following commands will place
network 10.2.3.0/19 into are 3?
a.)
Network 10.2.3.0 0.0.0.31 area 0
b.)
Network 10.2.3.0 0.0.0.31 area 3
c.)
Network 10.2.3.0 0.0.31.255 area 3
d.)
Network 10.2.3.0 0.0.31.0 area 3
36.) What are reasons for creating OSPF in a hierarchical
design?
a.)
To decrease routing overhead
b.)
To speed up convergence
c.)
To confine network network instability to single
areas of the network
d.)
All of above
37.) In OSPF scenario any one single area is not
directly connected with backbone area. But organization requirement to make
connectivity that areas to all another single area, which think you apply on
it.
a.)
OSPF frame relay
b.)
OSPF virtual link
c.)
OSPF stub area
d.)
None of above
38.) Which is use of make OSPF totally stub-area?
a.)
Area 0 stub
b.)
Area 0 totally stub
c.)
Area 0 stub no-summary
d.)
Are 0 no-summary
39.) Which OSPF LSA type is considered as a ASBR
summary LSA?
a.)
LSA type 2
b.)
LSA type 3
c.)
LSA type 4
d.)
LSA type 5
40.) NSSA stand for _____ ?
a.)
Non-so-standard area
b.)
Not-so-stub area
c.)
Not-so-stubby-area
d.)
All of above
41.) What is AD value of internal BGP?
a.)
20
b.)
200
c.)
177
d.)
178
42.) To create neighbourhood relationship, a router
running BGP sends an _____ message.
a.)
Open
b.)
Update
c.)
Keep alive
d.)
Close
43.) Why we are use Route redistribution?
a.)
Mergers when different IGPs are used.
b.)
Mergers when the same IGP is used.
c.)
Different company division are under separate
control for business or political reason.
d.)
All of above
44.) What command can be used to view the
configuration of a key chain used by OSPF?
a.)
Show key chain
b.)
Show key-chain
c.)
Show authentication key chain
d.)
Show eigrp key chain
45.) Which of the following is not true regarding
cisco IOS default setting for administrative distance?
a.)
EIGRP external : 90
b.)
OSPF internal : 110
c.)
RIP : 120
d.)
None of above
========= THANKS FOR VIEWING ==========
